Glossary entry

English term or phrase:

barrelling of the pinion.

Russian translation:

утончение профиля зубьев (малой) шестерни

Added to glossary by Enote
Feb 12, 2020 13:12
4 yrs ago
9 viewers *
English term

barrelling of the pinion.

English to Russian Tech/Engineering Energy / Power Generation GEARS
SPECIAL-PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
GEAR ELEMENTS
Vendor shall comment on gear design being apex leading or lagging and barrelling of the pinion.

Спасибо
Change log

Feb 14, 2020 13:44: Enote Created KOG entry

Proposed translations

3 hrs
Selected

утончение профиля зубьев (малой) шестерни

Сабж (barrelling) - это коррекция профиля зуба (шестерни) в строну его утончения. Посмотрим на описание сабжа у них
Цитата из http://www.tandwiel.info/en/gears/tooth-form-corrections/ (там есть рисунки)
2 Barreling and end relief
The barreling and the end relief are tooth shape corrections in axial sense. At the barreling the tooth thickness reduces slightly from the middle of the tooth to the sides according to a convex profile.
At alignment errors the load remains roughly in the middle of the tooth and one avoids lateral tooth forces, there where the tooth can capture less load. Barreling also allows greater alignment errors when mounting with a retention of a central tooth load.
...
3 Tooth tip barreling
The tooth tip is milled convexly across the entire tooth width. This type of gear is applied with tooth couplings to allow a certain alignment error at the connected shafts.
Еще одно определение сабжа в том же смысле, но с другим направлением утончения приведено в стандарте ISO 21771:2007 Gears — Cylindrical involute gears and gear pairs — Concepts and geometry, статья 6.2.3. этого стандарта с определением сабжа и рисунком воспроизведена тут https://www.smartmt.com/wp-content/uploads/7CylindricalGearM...
6.2.3 Profile crowning (barrelling), Cα
Profile crowning is the continuously increasing relief of the transverse profile from a common defined point of the main geometry (diameter, length of roll, roll angle) in the direction of the tip and root of the gear teeth. See Figure 27.
Т.е. этот термин описывает утончение в трех разных направлениях - продольном (бочкообразное), радиальном и верхушки зуба
Something went wrong...
4 KudoZ points awarded for this answer.
17 mins
English term (edited): barrelling of the pinion

нарезание бочкообразных зубьев на шестерне

.

--------------------------------------------------
Note added at 20 mins (2020-02-12 13:33:34 GMT)
--------------------------------------------------

Gear crowning/barrelling

Crowned gears are necessary where noise is a concern. Crowning gear teeth reduces noise by alleviating misalignment through either assembly or thrust problems.

Our barrelling machines are used for cleaning and polishing metal and plastics and can give a variety of finishes included matt and shine.



http://www.bandhgears.co.uk/gear_crowning.php

--------------------------------------------------
Note added at 21 mins (2020-02-12 13:34:04 GMT)
--------------------------------------------------

crowning teeth cutting - нарезание бочкообразных зубьев
http://www.multitran.com/m.exe?s=нарезание бочкообразных зуб...

--------------------------------------------------
Note added at 24 mins (2020-02-12 13:37:27 GMT)
--------------------------------------------------

ГОСТ 16530-83. ПЕРЕДАЧИ ЗУБЧАТЫЕ. Общие термины, определения и обозначения

1.7.3. Бочкообразная модификация зуба

Бочкообразная модификация

Продольная модификация зуба, в результате которой номинальная линия зуба начинает в средней части отклоняться от теоретической линии зуба в его тело с монотонным возрастанием отклонения по мере удаления от середины зуба к его торцам

http://docs.cntd.ru/document/gost-16530-83

--------------------------------------------------
Note added at 4 hrs (2020-02-12 17:22:08 GMT)
--------------------------------------------------

Благодаря наклону и бочкообразной форме зубьев конические колеса с круговым зубом более прочны, бесшумны (см. выше Crowning gear teeth reduces noise) и допускают большие отклонения при: монтаже, чем прямозубые.  [17]

Для нарезания цилиндрических шестерен с бочкообразной формой зуба на зубофрезерных станках устанавливается специальное копирное приспособление.

http://www.ngpedia.ru/id566448p2.html
Something went wrong...
Term search
  • All of ProZ.com
  • Term search
  • Jobs
  • Forums
  • Multiple search