Glossary entry (derived from question below)
polski term or phrase:
zac.
angielski translation:
tightening torque
Added to glossary by
Frank Szmulowicz, Ph. D.
Apr 8, 2018 15:14
6 yrs ago
1 viewer *
polski term
USA
English-Polish Translator/Interpreter
Native in: polski (Variant: Standard-Poland)
Works in: polski > angielski, angielski > polski
zac.
polski > angielski
Technika/inżynieria
Lotnictwo/kosmonautyka
airplanes
[samolot MiG-29]
Uwaga: 1. Dopuszcza się założenie podkładki dodatkowej lub wymianę na nową σ = 2 mm.
2. Śruby dociągać ręcznie do oporu kluczami dynamometrycznymi:
c. dla śrub Ø 8 mm M zac. = 160 ±10 kGcm;
d. dla śrub Ø 10 mm M zac. = 350 ±10 kGcm;
e. dla śrub Ø 12 mm M zac. = 640 ±10 kGcm.
Uwaga: 1. Dopuszcza się założenie podkładki dodatkowej lub wymianę na nową σ = 2 mm.
2. Śruby dociągać ręcznie do oporu kluczami dynamometrycznymi:
c. dla śrub Ø 8 mm M zac. = 160 ±10 kGcm;
d. dla śrub Ø 10 mm M zac. = 350 ±10 kGcm;
e. dla śrub Ø 12 mm M zac. = 640 ±10 kGcm.
Proposed translations
(angielski)
| 3 | tightening torque |
Frank Szmulowicz, Ph. D.
|
Change log
Aug 13, 2018 03:27: Frank Szmulowicz, Ph. D. Created KOG entry
Proposed translations
35 min
Frank Szmulowicz, Ph. D.
USA
USA
Native in polski
&
angielski
Specializes in field
USA
On time, on target, on budget.
Native in: angielski 
, polski
Works in: polski > angielski, angielski > polski, rosyjski > polski, and 1 more.
Related KudoZ points
:
152
Selected
tightening torque
klucz dynamometryczny = torque wrench
Tightening torque results in clamping force.
ccccc
A very common method for checking the tightening torque is to use a click wrench, which is a torque wrench equipped with a clutch that can be pre-adjusted to a specific torque. If the torque is greater than the preset torque value the clutch will release with a click.
https://www.atlascopco.com/content/dam/atlas-copco/industria...
--------------------------------------------------
Note added at 38 mins (2018-04-08 15:52:39 GMT)
--------------------------------------------------
cccccccccc
(here in foot-pounds, not kilogram force-centimeters)
Tightening Torque Guide for Grade 5 & 8 Hex Cap Screws
These Figures represent an estimate of torque (torque being the measurement of friction, not tension) required to induce given preload (clamp load) in a bolt for non-critical applications only. For critical or special applications where greater control is desired this should be experimentally determined. This applies to washer faced or double chamfered hex nuts (or bolts, if bolt is torqued) having a width across flats of approximately 1.5 times the nominal diameter and having threads free of interference.
http://www.almabolt.com/pages/catalog/bolts/tighteningtorque...
--------------------------------------------------
Note added at 51 mins (2018-04-08 16:06:01 GMT)
--------------------------------------------------
ccccccccccccccccccc
Zac. jest skrótem od zacisku, czyli clamping, ale clamping load jest siłą, a kG-cm jest momentem obrotowym, czyli tightening torque.
ccccccccccccccccccccccccccccccccccccccccccc
Tightening torque results in clamping force.
ccccc
A very common method for checking the tightening torque is to use a click wrench, which is a torque wrench equipped with a clutch that can be pre-adjusted to a specific torque. If the torque is greater than the preset torque value the clutch will release with a click.
https://www.atlascopco.com/content/dam/atlas-copco/industria...
--------------------------------------------------
Note added at 38 mins (2018-04-08 15:52:39 GMT)
--------------------------------------------------
cccccccccc
(here in foot-pounds, not kilogram force-centimeters)
Tightening Torque Guide for Grade 5 & 8 Hex Cap Screws
These Figures represent an estimate of torque (torque being the measurement of friction, not tension) required to induce given preload (clamp load) in a bolt for non-critical applications only. For critical or special applications where greater control is desired this should be experimentally determined. This applies to washer faced or double chamfered hex nuts (or bolts, if bolt is torqued) having a width across flats of approximately 1.5 times the nominal diameter and having threads free of interference.
http://www.almabolt.com/pages/catalog/bolts/tighteningtorque...
--------------------------------------------------
Note added at 51 mins (2018-04-08 16:06:01 GMT)
--------------------------------------------------
ccccccccccccccccccc
Zac. jest skrótem od zacisku, czyli clamping, ale clamping load jest siłą, a kG-cm jest momentem obrotowym, czyli tightening torque.
ccccccccccccccccccccccccccccccccccccccccccc
4 KudoZ points awarded for this answer.
Discussion